Bateson 0844
Tyre pressures and wheel nut / bolt torque
Tyre specification
Fitment details
- Pressure applies to the 145R10 tyre after normalising Bateson's product-page notation to the matching support-table size.
- The product page does not identify the wheel fixing.
- Select a torque only after checking whether the trailer has a removable wheel bolt or a nut on a fixed stud and confirming the thread; socket size alone is not sufficient.
- Bateson's published alternatives are 3/8 UNF 60 Nm, M12 × 1.5 bolt 90 Nm, M12 × 1.5 nut 100 Nm and M16 × 1.5 nut 195 Nm.
- Options and production changes may alter weights, dimensions, tyres and wheel equipment; check the trailer plate and fitted components.
- Internal dimensions: length 2.5 m × width 1.25 m × height 0.3 m.
- Overall dimensions: length 3.85 m × width 1.76 m.
Choose the setting for the confirmed wheel fixing.
Socket size alone does not identify the thread.
Alloy wheels are not covered by these settings.
Tyre pressure placard

Official Bateson 0844 product-page photograph with the optional ramp door and lifting springs.
| Tyre size | kPa | PSI | bar |
|---|---|---|---|
| 145R10 | 240 | 35 | 2.4 |
Please ensure the maximum pressure marked on your tyre sidewall is equal to or higher than the pressure listed here.
A tyre of the same size with a lower pressure rating may have been fitted by mistake.
Never exceed the maximum pressure marked on the tyre.
Is your tyre load rating high enough?
Find the load index beside the tyre size. For example, 104 = 900 kg per tyre. For normal trailer wheels, use the first number in 104/102N. The second is for tyres mounted side by side on one hub, not a trailer with two axles. N is the speed symbol.
Open the tyre load rating conversion chart →
Capacity per tyre × number of road tyres = combined tyre capacity. Do not count the spare or jockey wheel.
Example: four tyres rated 104 give 900 × 4 = 3,600 kg, which exceeds a 3,500 kg trailer maximum gross weight by 100 kg. This is a total-capacity comparison only.
Check your tyre capacity
Enter all three values to compare capacity.
Check every axle too: its tyres must support its plated maximum axle weight, and no individual tyre may be overloaded. This calculator assumes all tyres have the same load index and are mounted singly. It does not confirm fitment or set tyre pressure. Keep the trailer manufacturer’s required load and speed ratings, use the specified cold pressure and check the actual loaded axle weights.
Cold tyre pressure
35 PSI / 2.4 bar / 240 kPa
A separate unloaded or fully laden pressure has not been confirmed for this entry.
Wheel nut / bolt torque
Use the setting only for the wheel and fixing specification described above.
Frequently asked questions
What is the tyre pressure for the Bateson 0844 general-purpose trailer with 145R10 tyres?
The tyre pressure for the Bateson 0844 general-purpose trailer with 145R10 tyres is 35 PSI (2.4 bar / 240 kPa), measured cold. This applies to the 145R10 tyre matched to Bateson's support table. Confirm the exact sidewall marking and load rating before use.
What is the wheel nut or bolt torque for the Bateson 0844 general-purpose trailer?
The wheel nut or bolt torque for the Bateson 0844 general-purpose trailer depends on the fitted fixing. 3/8 UNF wheel nut (confirm socket on the trailer): 60 Nm; M12 × 1.5 wheel bolt (normally a 19 mm socket): 90 Nm; M12 × 1.5 wheel nut (confirm socket on the trailer): 100 Nm; M16 × 1.5 wheel nut (normally a 27 mm socket): 195 Nm. Identify whether the wheel uses a removable bolt or a nut on a fixed stud, then confirm the thread. Use only the matching Bateson setting; socket size alone does not identify the fixing.