Bateson 520

Tyre pressures and wheel nut / bolt torque

Tyre specification

Tyre size16.5-6.5x8

Fitment details

  • The Bateson model page lists 16.5-6.5x8 tyres.
  • Bateson's support table specifies 43 PSI / 3.1 bar; the kPa figure is the corresponding rounded metric value.
  • The model page does not identify the fitted wheel thread or whether the fixing is a bolt or nut.
  • Use only the matching Bateson wheel-fixing setting after checking the fitted hardware; socket size alone does not identify the thread.
  • Internal body: 2.10 m long x 1.25 m wide x 0.30 m high; overall: 3.15 m long x 1.39 m wide x 0.80 m high.
  • Bateson does not map this model to one wheel fixing, so the conditional list retains the published 3/8 UNF and M12 settings only.
  • Internal dimensions: length 2.1 m × width 1.25 m × height 0.3 m.
  • Overall dimensions: length 3.15 m × width 1.39 m × height 0.8 m.
Warning — Check wheel fixing

Choose the setting for the confirmed wheel fixing.

Socket size alone does not identify the thread.

Alloy wheels are not covered by these settings.

Click here to read more about tyre load ratings →

Tyre pressure placard

Bateson 520
UNLADEN WEIGHT132 kgMAX GROSS WEIGHT550 kg
Bateson 520 trailer

Official Bateson 520 photograph with optional mesh sides, ramp door and jockey wheel; equipment may vary.

Tyre sizekPaPSIbar
16.5-6.5x8310433.1
Warning — Check tyre pressure rating

Please ensure the maximum pressure marked on your tyre sidewall is equal to or higher than the pressure listed here.

A tyre of the same size with a lower pressure rating may have been fitted by mistake.

Never exceed the maximum pressure marked on the tyre.

Is your tyre load rating high enough?

EXAMPLE TYRE SIDEWALL MARKING 195/60R12C104/102N Single-wheel load indexDual-wheel load index104 = 900 kg per tyre102 = 850 kg per tyreOne wheel at eachend of the axleTwo wheels side by sideat each end of the axleTwin axles do not mean dual wheels. N is the speed symbol.

Find the load index beside the tyre size. For example, 104 = 900 kg per tyre. For normal trailer wheels, use the first number in 104/102N. The second is for tyres mounted side by side on one hub, not a trailer with two axles. N is the speed symbol.

Open the tyre load rating conversion chart →

Capacity per tyre × number of road tyres = combined tyre capacity. Do not count the spare or jockey wheel.

Example: four tyres rated 104 give 900 × 4 = 3,600 kg, which exceeds a 3,500 kg trailer maximum gross weight by 100 kg. This is a total-capacity comparison only.

Check your tyre capacity

Enter all three values to compare capacity.

Check every axle too: its tyres must support its plated maximum axle weight, and no individual tyre may be overloaded. This calculator assumes all tyres have the same load index and are mounted singly. It does not confirm fitment or set tyre pressure. Keep the trailer manufacturer’s required load and speed ratings, use the specified cold pressure and check the actual loaded axle weights.

Cold tyre pressure

43 PSI / 3.1 bar / 310 kPa

A separate unloaded or fully laden pressure has not been confirmed for this entry.

Wheel nut / bolt torque

3/8 UNF wheel nut (confirm socket on the trailer)60 Nm
M12 wheel bolt · 19 mm90 Nm
M12 wheel nut (confirm socket on the trailer)100 Nm
M16 wheel nut · 27 mm195 Nm

Use the setting only for the wheel and fixing specification described above.

Frequently asked questions

What is the tyre pressure for the Bateson 520 unbraked trailer with 16.5-6.5x8 tyres?

The tyre pressure for the Bateson 520 unbraked trailer with 16.5-6.5x8 tyres is 43 PSI (3.1 bar / 310 kPa), measured cold. This applies to the Bateson-listed 16.5-6.5x8 tyre. Check the fitted tyre size, construction marking and sidewall pressure limit before use.

What is the wheel nut or bolt torque for the Bateson 520 unbraked trailer?

The wheel nut or bolt torque for the Bateson 520 unbraked trailer depends on the fitted fixing. 3/8 UNF wheel nut (confirm socket on the trailer): 60 Nm; M12 × 1.5 wheel bolt (normally a 19 mm socket): 90 Nm; M12 × 1.5 wheel nut (confirm socket on the trailer): 100 Nm; M16 × 1.5 wheel nut (normally a 27 mm socket): 195 Nm. Identify whether the wheel uses a removable bolt or a nut on a fixed stud, then confirm the thread. Use only the matching Bateson setting; socket size alone does not identify the fixing.

Other Bateson trailer models →