Indespension LT07584

Tyre pressures and wheel nut / bolt torque

Tyre specification

Tyre size20.5 x 8-10 4/77M

Fitment details

  • Applies to the ISWT030 4 x 3/8 in on 101.6 mm PCD wheel assembly.
  • The current product page confirms LT07584.
  • The current livestock category gives 4 x 3/8 in studding on 101.6 mm PCD, while the official catalogue gives the model's 20.5 x 8-10 tyre, 323 kg unladen weight and dimensions.
  • ISWT030 is the sole official wheel-table entry matching all three wheel fields and carries the 35 PSI pressure.
  • The care pack gives 57 Nm for 3/8 in wheel nuts.
  • Overall dimensions are not published in the reviewed official sources.
  • Internal dimensions: length 2.45 m × width 1.2 m × height 1.2 m.

Tyre pressure placard

Indespension LT07584
UNLADEN WEIGHT323 kgMAX GROSS WEIGHT750 kg
Indespension LT07584 trailer

Official Indespension LT07584 photograph; equipment and options may vary.

Tyre sizekPaPSIbar
20.5 x 8-10 4/77M241352.41
Torque applies to the wheel assembly specified in Fitment details.
Warning — Check tyre pressure rating

Please ensure the maximum pressure marked on your tyre sidewall is equal to or higher than the pressure listed here.

A tyre of the same size with a lower pressure rating may have been fitted by mistake.

Never exceed the maximum pressure marked on the tyre.

Is your tyre load rating high enough?

EXAMPLE TYRE SIDEWALL MARKING 195/60R12C104/102N Single-wheel load indexDual-wheel load index104 = 900 kg per tyre102 = 850 kg per tyreOne wheel at eachend of the axleTwo wheels side by sideat each end of the axleTwin axles do not mean dual wheels. N is the speed symbol.

Find the load index beside the tyre size. For example, 104 = 900 kg per tyre. For normal trailer wheels, use the first number in 104/102N. The second is for tyres mounted side by side on one hub, not a trailer with two axles. N is the speed symbol.

Open the tyre load rating conversion chart →

Capacity per tyre × number of road tyres = combined tyre capacity. Do not count the spare or jockey wheel.

Example: four tyres rated 104 give 900 × 4 = 3,600 kg, which exceeds a 3,500 kg trailer maximum gross weight by 100 kg. This is a total-capacity comparison only.

Check your tyre capacity

Enter all three values to compare capacity.

Check every axle too: its tyres must support its plated maximum axle weight, and no individual tyre may be overloaded. This calculator assumes all tyres have the same load index and are mounted singly. It does not confirm fitment or set tyre pressure. Keep the trailer manufacturer’s required load and speed ratings, use the specified cold pressure and check the actual loaded axle weights.

Cold tyre pressure

35 PSI / 2.41 bar / 241 kPa

A separate unloaded or fully laden pressure has not been confirmed for this entry.

Wheel nut / bolt torque

57 Nm

Use the setting only for the wheel and fixing specification described above.

Frequently asked questions

What is the tyre pressure for the Indespension LT07584 livestock trailer with 20.5 x 8-10 4/77M tyres?

The tyre pressure for the Indespension LT07584 livestock trailer with 20.5 x 8-10 4/77M tyres is 35 PSI (2.41 bar / 241 kPa), measured cold. This applies to the specified ISWT030 20.5 x 8-10 4/77M wheel assembly. Confirm the tyre marking and fitted wheel attachment before use.

What is the wheel nut or bolt torque for the Indespension LT07584 livestock trailer?

The wheel nut or bolt torque for the Indespension LT07584 livestock trailer is 57 Nm. This applies to the documented 3/8 in wheel nuts on fixed studs; Indespension specifies 57 Nm for this attachment.

Other Indespension trailer models →